Posts

Expert Tile & Grout Cleaning

cleaning tile & grout floors

How we do it:

There are actually 4 components working together in harmony that allow us to achieve these superior cleaning results.

Emulsifier – We use a non toxic, environment friendly spray that is applied to the tile & grout floor to quickly loosen up the soil.

High Pressure – Our advanced patented equipment produces water pressure that can be adjusted between 200 and 1500 psi to penetrate even the toughest areas!

Heat – Our powerful truck mounted steam cleaner is capable of maintaining temperatures over 230 degrees throughout the cleaning process.

Vacuum – Our Vacuum process surgically lifts the soil and dirty water off your floor.

Other amazing videos at real job sites

 

 

 


 

Replacing cracked or loose tiles.

 

Why are my tiles cracking and grout falling out?

There are many reasons why tiles crack or become loose. The most common reason is poor installation. There are many short cuts installers can take to save time or money, most may not be noticeable for a year or two, long after the job is done. By this time the installer is nowhere to be found. Before tile can be installed the floor should be prepared with a suitable cement backer board. The board should be layed in thin set, and screwed down as well as making sure all seams are taped.

After the sub floor has been prepared with backer board the tile can be set in thin set. For larger jobs there should be at least 2 installers to ensure the thin set does not start to set up be for the tile is placed on it. It is also advisable to butter the back of each tile, another step that is often skipped because it just takes more time.

Pristine highly recommends using a company that specializes in installing tile, not just a handyman or a family member. You will be much happier with your floor in the long run. Pristine has two personal favorites J & J tile and Marble or quality carpet and floor(Bob Mcdonald or Scott Busby can help you). Please trust me on this, I get call after call from folks who’s floor is failing because they tried to save money on the install.

So… after all that has been said, can we fix your floor?

sometimes… it depends on the severity of the problem. If it is just a few tiles or a small area that has become a problem we can carefully remove the tiles, grind down the old thin set and re-set the tiles, as shown in the photos. If the problem is widespread through out the majority of the floor, chances are, it was a really poor installation job and needs to be done over.

One last tip on installing floors…always, always, always save some leftover tile for repairs and even take note of the grout color and where it came from. This makes certain that any future repairs will look great! The biggest problem we face is that people have cracked or broken tiles and no spares. Once the floor is installed the tile will become obsolete and nowhere to be found in less than a year.

 

pristinetg.com

When the grout and caulk need to be replaced.

 

Many times we get calls for shower tile cleaning, but sometimes the caulk and grout are just too far gone for cleaning alone, as shown in the photos below from this home in Fredericksburg Va.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Yuck! who would want to get in that shower? (Sorry for the thumb)

It is always a great idea to inspect your showers, tubs, and sinks for signs of a problem, such as missing or cracked grout and/or caulk. Often small problems can be rectified before they turn into big expensive problems. In the case above it actually looked a lot worse than it was. The grout and caulk were in bad shape but miraculously the water had not penetrated to the wall board just yet. Pristine was able to go in and clean the tile, remove and replace all the old grout and caulk and make this shower look new and inviting once again!

Some folks are not quite as lucky and repairing or replacing often are needed.  If the tiles are loose and the walls feel spongy you can bet damage has taken place. Sometimes we can cut out a bad section and make the necessary repairs, if the damage is not too extensive.

The photos below, believe it or not, are the same shower fully restored!

The picture below is of a counter restoration project we did in the city of Fredericksburg Va 22401,

old tile counter top looks new again

 

 

 

 

 

 

 

 

 

 

 

Tile & Grout Cleaning

 

Do I have to seal my grout?

Yes!

The two main types of grout are sanded and unsanded, sanded is used in larger grout joints and unsanded in smaller joints. The sand is added to the grout to give it strength, but also leaves a rough texture. This porous rough texture absorbs spills, dirty mop water, outdoor soil and so on, making it difficult to clean. In no time the grout will be stained, discolored, and just plain ugly. Using a quality sealer on the grout will help prevent permanent staining, as well as make cleaning easier. The misunderstanding is… people think sealer will keep their grout clean. The fact is sealer will only provide a barrier, thus making cleaning easier and permanent damage less likely, soil will still find its way to the floor, if I had the answer to preventing that, I would be a hero, and probably out of business. The unsanded grout ussually found on walls, and in showers, is much less porus, but still can benifit from sealer especially in a shower. There are often minerals in the water that can even leave unsanded grout stained after time, especially white grout.